They are used to generate a controlled vibration required to feed and sort the parts inside a bowl conveniently provided with the drive. Activated by an electromagnet, they require an electronic controller and (optionally) a probe to monitor and compensate the parameters of the vibration. Power supply voltage is 230V 50Hz monophase. On request, they can be provided with different voltages or frequencies.
Vibratory driving units for linear feeders
They are used to generate, by means of a controlled vibration, the advancements of the parts inside a rail or an hopper conveniently provided with the drive. Activated by an electromagnet, they require an electronic controller and (optionally) a probe to monitor and compensate the parameters of the vibration. Power supply voltage is 230V 50Hz monophase. On request, they can be provided with different voltages or frequencies.
Conical bowls for vibratory feeders
They are used to contain, feed and sort the pieces travelling along their track. Actuated by means of Brovind vibratory driving units, the bowls can be supplied as “standard” manufactured in AISI 304 stainless steel or polyamide, or as “custom” according to the needs of required materials (e.g. AISI 316 stainless steel) or dimensions (coil width, pitch etc…). They can also be covered with anti-oil or anti-wear coatings.
Stepped bowls for vibratory feeders
They are used to contain, feed and sort the pieces travelling along their track. Actuated by means of Brovind vibratory driving units, the bowls can be supplied as “standard” manufactured in AISI 304 stainless steel or polyamide, or as “custom” according to the needs of required materials (e.g. AISI 316 stainless steel) or dimensions (coil width, pitch etc…). They can also be covered with anti-oil or anti-wear coatings.
Cylindrical bowls for vibratory feeders
They are used to contain, feed and sort the pieces travelling along their track. Actuated by means of Brovind vibratory driving units, the bowls can be supplied as “standard” manufactured in AISI 304 stainless steel or polyamide, or as “custom” according to the needs of required materials (e.g. AISI 316 stainless steel) or dimensions (coil width, pitch etc…). They can also be covered with anti-oil or anti-wear coatings.
Vibratory driving units ATEX comply
Activated by a pneumatic pulsator, the AIR driving units are used to generate the advancement of the parts inside a channel or a bowl in environments where there is a risk of fire or explosion, both due to gas or powders
Digital controllers
The new generation of electronic controllers by Brovind: interface panel with buttons, signal & command inputs and outputs, microprocessor to manage the parameters of vibration. The CFV model, top of the range, in addition allows the control both of the amplitude and the frequency of the command signal, both in manual and automatic mode (thanks to Brovind SRV-02 accelerometric probe). This means a better control of the parameters of the vibration and the possibility of adaptation and compensation of the command to the changes on the mechanichal conditions (variation in the load of material, springs wear, loose of the fixing means). Furthermore, it is possible to obtain the independency of the power supply to the feeding system from the local electrical power line; it is in fact possible to test the feeding system on a 50 Hz line then send it in countries with 60 Hz without changing neither the internal coil of the drive neither the command board of the controller!
Digital controllers with potentiometer
Evolution of the analogical controllers for vibratory feeders, the new CB series merge the easiness of use of a potentiometer regulation with the performances of a modern microprocessor architecture. Both models allows an automatic compensation of power line voltage variations, start/stop with PNP proximity and external 0-10V / 4-20mA command.
The CB02 model can be equipped with Brovind accelerometric probe, in order to work in automatic mode for vibration control. Both models are available in “bulk” version, ready to be mounted on DIN rails inside an electrical cabinet.
Step feeders
With its plated modular elevators, Brovind introduces a complementary technology to the vibratory feeders, thus allowing Brovind to widen the range of possibilities to realize a feeding and sorting system. Manufactured in vertical execution, they allows the lifting and dosing of products mantaining contained sizes and significant flow-rates; by means of reciprocating plates system, the material is collected in small quantities and lifted up to the exit point, where a linear feeder suitably manufactured feeds and sorts the parts. They can be realized with pneumatic or motorized drive, both in “standard” and “custom” versions, for example with the possibility to modify loading capacity of the hopper or the thickness of the plates.
Vibratory loading hoppers
Particularly suited to feed and pre-dose small sized parts. They are operated by means of a Brovind vibratory linear drive, the model varying according to the size of the hopper required.
Motorized loading hoppers
Particularly suited to feed and pre-dose small-sized parts, in particular those that can tangle up. They are operated by an electric motor and can be placed with an angle from 0 to 25°, according to the needs. Depending on the product to be fed and the required slope, different belts can be used, for example flat, smooth, with plugs, in different materials.
All models are also available in AISI 316 stainless steel for food/pharmaceutical use.
Vibratory hopper channels
Particularly suited to feed and pre-dose small sized parts. They are operated by means of a Brovind vibratory linear drive, the model varying according to the size of the hopper required.
Soundproofing and safety hoods
Brovind designs and manufactures its own soundproofing and safety enclosures for its automatic feeding systems.
In addition to the standard products range, both in “drop” design and cylindrical, it is also possible to design and realize customized solutions according to particular requests.
